#N1mm logger for mac update#
#N1mm logger for mac software#
#N1mm logger for mac Pc#
#N1mm logger for mac mac#
#N1mm logger for mac windows#

Make sure that the entry category is compatible with multiple operating positions. Create a new database (*.mdb) on the master station (station zero). Type them exactly the same on each workstation.Д§. Use these numbers and names to fill out the table under >config > edit station names. Make a list of operating station number (beginning with zero), the station label, and the static IP address.

#N1mm logger for mac Pc#

Any port that controls the rig or does something else useful should be enabled as part of Parallels configuration, and the virtual PC should control it.Д¦. Make sure the computers and their respective rigs work right in single user mode.

#N1mm logger for mac update#

Set up the individual virtual computers - as usual, before the contest, download the latest update for N1MM and data files (wl_city.dta and master.dta).ДҐ. So, for us, we went into TCP/IP properties and set the gateway and DNS to the routerвЂ™s address (192.168.1.1), and then gave each PC itвЂ™s static IP (e.g., 192.168.1.200).Д¤. Next, set up the network configuration for the virtual PC using the same parameters as the Mac. When it comes up, it will share the same IP address as its host Mac. After clicking вЂњOKвЂќ, hit the green arrow to boot the VM. Click вЂњnetwork adapterвЂќ, and then select вЂњShared NetworkingвЂќ (rather than bridged). Now, click вЂњConfigurationвЂќ, which should bring up the configuration editor.

#N1mm logger for mac windows#

If you have more than one VM defined, select one of the Windows images. Looking at the router set up, we also avoided 192.168.1.100 to 192.168.1.150, as this address range was assignable. For instance, the router, 192.168.1.1 and the bedroom computer addresses 192.168.1.100 were avoided. We went with static ip addresses, avoiding the address range that had already been assigned by DHCP to other computers in the house. The topology doesnвЂ™t really matter, just as long as thereвЂ™s no switch between the computers. In fact, in our case, we ran one wire from the router to a dumb hub, and thence to each computer. We went with a wired connection to each computer. From past experience, N1MM does not do well with wireless internet - it uses UDP packets, and perhaps isnвЂ™t very tolerant when some drop out due to RF interference.

In our case, the house was connected to cable-provided internet via a Linksys wireless router.

#N1mm logger for mac software#

That is, they should all be on the same LAN and local software firewalls should at least allow responses to pings (ICMP). Set up the network so all the machines can ping one another (using the OS X terminal). IвЂ™ll only point out the big steps and those that are Mac-specific.Дў.

#N1mm logger for mac mac#

Most of the instructions are the same whether youвЂ™re on a PC or a Mac emulating a PC. Flip to the page on вЂњMulti-User SupportвЂќ.

Pull down the latest version of the documentation for N1MM. Before those neurons completely evaporate, hereвЂ™s what I remember:ДЎ.

Clearing Rttyrite Sections from writelog.After Operation Sizzling Pork, I thought it would be a good idea to write down how we had managed to run N1MM in multioperator mode using MacBooks at each operating position.

Once you have MMTTY set up in DI-1, you are now ready to Set up 2Tone in a Receive-only Digital Interface window. Once you have MMTTY working, then go back to N1MM. The best way to troubleshoot is to close N1MM and open the standalone MMTTY program. If you are not printing the signal or see the presence of noise in the RTTY Engine 1В window, then something is not set up correctly. Note: With your radio on, tune in a RTTY signal. (If your radio is turned on and MMTTY has already been set up to receive on your sound card, you may see the presence of noise in the display and you may see random noise characters in the Digital Interface window. Drag it away from other windows so they donвЂ™t overlap. The familiar MMTTY control panel, called вЂњRTTY Engine 1вЂќ, should appear as shown in Figure 3-5. Go to the Interface pull-down menu at the top of the Digital Interface window and select MMTTY as shown in Figure 3-3. If the Main Entry Window is on top of the Digital Interface window, move the Main Entry Window away from the Digital Interface window so they donвЂ™t overlap each other. The Digital Interface (DI)В window opens up to MMVARI by default.